ShieldSledding

版本 v1.1.1·更新於 2026-09-27

Sled on your equipped shield.

模組介紹 作者原文

Shield Sledding

Slide down hills on your equipped shield. Jump, press Mouse4 to arm (in the air or right after takeoff), then land to start sledding. Speed follows the slope; Blocking sets your max per shield ([ShieldCoastSpeeds] Skill0→Skill100). Defaults: wood 18→25 m/s; best board (Nord Greatshield) 28.8→40 at Blocking 100.

Valheim 1.0 / Deep North boards are included: Nord Shield, Nord Buckler, and Nord Greatshield. Ice sheets and floes are faster and slipperier than snow. Sledding through Deep North powder leaves the same compacted trail as walking.

Works in multiplayer. Everyone playing needs the mod installed.

Optional: WoodRamps adds buildable wood ramps for custom sled runs. Not required.

Questions or bugs? Discord

Install with r2modman

  • Install r2modman.
  • Pick Valheim and open the Default profile.
  • Install BepInExPack Valheim if it is not already there.
  • Either:
  • Search for Shield Sledding and install it, or
  • Settings → Import local mod and pick dist\ShieldSledding-1.1.1.zip.

Manual install

  • Install BepInExPack Valheim.
  • From the Release folder, copy the ModdedWolf-ShieldSledding folder into Valheim:

Valheim\BepInEx\plugins\ModdedWolf-ShieldSledding\

You should end up with:

Valheim\BepInEx\plugins\ModdedWolf-ShieldSledding\ShieldSledding.dll

  • Launch Valheim through BepInEx (Steam with the BepInEx launcher, or whatever you normally use).

Config shows up after the first run at:

BepInEx\config\ModdedWolf.ShieldSledding.cfg

How to use it

  • Equip a shield that still has durability (drawn in hand — sheathed does not count).
  • Jump on purpose — walking off a cliff without pressing jump does not count.
  • Press your ActivationKey while airborne or right after takeoff (default Mouse4, changeable in config). In-game hints always show the key you have set. Without a shield equipped, the key does nothing.
  • Land to start sledding. By default any ground works; raise MinimumSlope in config if you want steeper hills only.

Valheim 1.0 uses G for a vanilla action, so the default sled bind is Mouse4. Existing configs that were still on G are migrated automatically; a custom bind is kept.

Controls while sledding

| Key | What it does |

|-----|----------------|

| A / D | Steer (screen left/right; InvertSteering / CameraRelativeSteering in config) |

| W | Lean forward, small speed boost (ground or water only) |

| S | Brake (ground or water only) |

| Space | Jump — you stay in sled mode |

| ActivationKey | Arm in the air after a jump; quit sledding (in-game hints show this key) |

| Esc | Quit sledding |

Sled audio is one toggle under [Effects]: EnableSoundEffects (slide, wind, and impact together).

Sledding ends if you press your activation key or Esc, get hit by a creature or player, sink in deep water (too slow to skim), die, or your shield breaks from wear. At 6 m/s or faster you can skim across water instead of swimming.

Combat & damage while sledding

| Hit type | What happens |

|----------|----------------|

| Falls and impacts | No health loss — damage goes to shield durability instead |

| Creature or player attack | Knocked off the sled, staggered, no health loss |

While armed (after the activation key, before landing), hits are blocked with no shield wear — you stay on your feet.

Configurable in ModdedWolf.ShieldSledding.cfg under [Damage]: AbsorbDamageToShield, EndSledOnCombatHit, StaggerOnCombatHit.

Shield wear & speed (defaults)

Hard max speeds by shield and Blocking skill (m/s). Slope physics free below the cap. Edit under [ShieldCoastSpeeds] as Prefab_Skill0 / Prefab_Skill100. Wear is durability drain while sledding (lower = lasts longer).

| Shield | Wear | Max @ Blocking 0 | Max @ Blocking 100 |

|--------|------|--------------------|----------------------|

| Wood | 6.00× | 18.0 | 25.0 |

| Wood tower | 5.60× | 18.5 | 25.8 |

| Bronze buckler | 3.50× | 19.1 | 26.5 |

| Bone tower | 4.20× | 19.6 | 27.3 |

| Iron buckler | 0.80× | 20.2 | 28.0 |

| Banded | 2.00× | 20.7 | 28.8

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

denikson-BepInExPack_Valheim

檔案與校驗

檔案名稱
ShieldSledding-1.1.1.zip
檔案大小
213.7 KiB