Passive Trinket Modifiers
Standalone configurable trinket effects for Valheim with passive and doubled configuration sections. Lets you configure each trinket's ability, and chose any modifier so that each trinket can do anyth
模組介紹 作者原文
Trinket Modifiers
Current version: 0.32.1
This is a standalone configurable passive-effect engine for the 13 Better Trinkets prefabs plus the Deep North Neckstabber and Witch Crown trinkets. It scans every inventory position, so a dedicated trinket-slot mod is optional.
Do not run the original BetterTrinkets DLL alongside this plugin. This project is intended to replace its passive-effect handling.
Configuration
Every trinket has two sections:
- [Trinket Name] contains passive values.
- [Trinket Name.Doubled] contains values used while adrenaline doubling is active, plus Duration in seconds.
The initial supported defaults mirror the original Better Trinkets configuration. The original one-time health, stamina, and eitr entries are not included because this project intentionally uses persistent native SE_Stats effects only.
Available native fields in each section are:
- HealthRegenMultiplier, StaminaRegenMultiplier, EitrRegenMultiplier
- Armor, Speed, SwimSpeed, Jump, FallDamageMultiplier
- NoiseMultiplier, StealthMultiplier, MaxCarryWeight, TimedBlockBonus, StaggerMultiplier
- DamageModifier, plus BluntDamage, SlashDamage, PierceDamage, ChopDamage, PickaxeDamage, FireDamage, FrostDamage, LightningDamage, PoisonDamage, and SpiritDamage
- RunStaminaUseMultiplier, JumpStaminaUseMultiplier, AttackStaminaUseMultiplier, BlockStaminaUseMultiplier, DodgeStaminaUseMultiplier, SwimStaminaUseMultiplier, HomeItemStaminaUseMultiplier, and SneakStaminaUseMultiplier
- Resistance
- Skill1/Skill1Bonus, Skill2/Skill2Bonus, and RaiseSkill/RaiseSkillBonus
Skill1 and Skill2 use Valheim's native flat-skill slots. RaiseSkill uses the native skill-gain slot; its neutral multiplier is 1.0.
The stamina-use settings are config multipliers: 1.0 is unchanged, 0.75 means 25% less cost, and 1.25 means 25% more cost. The plugin converts these to Valheim's native additive fields, where 0.0 is neutral.
NoiseMultiplier, StealthMultiplier, and StaggerMultiplier use the same config convention: 1.0 is unchanged, while values below or above 1.0 reduce or increase the corresponding effect.
Global settings are in [General]:
- Enabled
- DebugLogging
- DoublingOnAdrenaline
- AdrenalineGainMultiplier — global, not per trinket; 0.0 disables adrenaline gain, 1.0 is unchanged, and 2.0 doubles adrenaline gain.
安裝與使用 安裝：BepInEx 外掛
- 本站下載的壓縮包就是模組本體，通常是 BepInEx 外掛（解壓後得到 .dll 或外掛資料夾）。
- 建議流程：用社群模組管理器（如 r2modman）選中本遊戲後匯入該模組，管理器會自動裝好 BepInEx 前置並處理依賴。
- 手動流程：先在遊戲目錄裝好 BepInEx 載入器，再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
- 啟動遊戲，BepInEx 控制台會列印載入日誌；確認這個模組出現在日誌裡即為安裝成功。
帶「前置依賴」的模組需要一併安裝，否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時，主機與所有用戶端需要安裝一致的模組。
下面這些內容需要先安裝，否則該模組不會生效：