LessGreyDwarfs
With Less GreyDwarfs, you decide how many twig-wielding nuisances are allowed to spawn
模組介紹 作者原文
Less Grey Dwarfs
Tired of every walk through the Black Forest turning into an unsolicited Grey Dwarf convention?
With Less Grey Dwarfs, you decide how many twig-wielding nuisances are allowed to spawn. Set your preferred spawn percentage, and the game will make sure the Grey Dwarf population never exceeds your limit.
Want a peaceful stroll? Set it low.
Want a mild infestation? Turn it up.
Want the entire forest to become a pebble-throwing nightmare? That’s between you and Odin.
Features:
Set the maximum Grey Dwarf spawn percentage
Reduce surprise forest ambushes
Spend less time fighting angry garden gnomes
Fully configurable to match your preferred level of woodland harassment
Because sometimes you want to explore the Black Forest without being personally responsible for a Grey Dwarf extinction event.
HOW IT WORKS
What the code does (per-attempt probability):
Every time the game tries to spawn a Greydwarf, it rolls a random number 0.0–1.0. If it rolls above 0.25 (75% of the time),
the spawn gets cancelled. If it rolls 0.25 or below (25% of the time), the spawn proceeds normally.
With per-attempt probability, you get:
Natural smoothing — it's always 25% odds, so the population naturally settles into a lower steady state without weird bursts
Works everywhere equally — doesn't matter if you're deep in the Black Forest or just passing through
No edge cases — a hard cap can break if other mods or events try to force-spawn
Still feels alive — you'll still see them, just not constantly
The math works out roughly like this: if the vanilla game naturally maintains ~12 Greydwarfs in your loaded area, with 25% per-attempt
odds it'll settle around ~3 at a time on average. Enough to keep the Black Forest feeling dangerous, not annoying.
So it's a 25% chance per spawn attempt — like a coin flip that only comes up heads a quarter of the time.
Configuration:
The config file is located in "\Bepinex\config" (You need to start the game at least once, with the mod installed to create the config file).
Enable Mod
Change GreyDwarf Spawn Percentage. 25% means No more than
Installation: (manual)
Use r2Modman for best results - automatic and easy
Manual Installation
Extract DLL from zip file into "\Bepinex\plugins" or use your favorite mod manager
Start the game.
Questions or need help?
Chat with me on Discord
Version Information:
1.0.2
- fixed logic to allow spanwing of all entities if the greydwarf spawning is disabled.
1.0.1
- code cleanup
1.0
- initial release
安裝與使用 安裝:BepInEx 外掛
- 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
- 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
- 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
- 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。
帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。
下面這些內容需要先安裝,否則該模組不會生效: