FlipIt

版本 v1.0.0·更新於 2026-09-11

Free placement rotation on any axis and any surface while building in Valheim.

模組介紹 作者原文

Flip It

Free placement rotation for Valheim building. Tilt, roll, and mount pieces on walls, ceilings, slopes, dirt, and roofs.

Valheim 1.0 compatible (Unity 6 / BepInExPack Valheim 5.4.2350).

Flip It is an independent, lightweight placement mod. It uses the same standard Valheim Harmony patch pattern as other rotation mods, but is not affiliated with ValheimPlus or PerfectPlacement.

Screenshots

Wall mounting

Angled surface placement

Vanilla behavior preserved

Ground placement

Tilt any direction

Controls

  • Scroll wheel — rotate on Y (vanilla, 22.5° per step)
  • Shift + scroll — pitch (X axis)
  • Ctrl + scroll — roll (Z axis)
  • J — reset current piece to vanilla upright orientation (rebindable)

Vanilla placement stays normal until you intentionally tilt with Shift or Ctrl.

Features

  • Full 3-axis ghost rotation while placing hammer pieces
  • Surface attach for non-build pieces only (portals, furniture, etc.) after tilting
  • Hammer Build and Heavy Build pieces: tilt + vanilla snap only (no surface-attach override)
  • Reset key (default J) returns the current piece to vanilla orientation
  • Client-side only; requires BepInExPack Valheim 5.4.2350+ for Valheim 1.0

Config

BepInEx/config/hardwire99.flipit.cfg

  • RotationStepDegrees — pitch/roll step when not matching vanilla (default 22.5; use 90 for quarter turns)
  • MatchVanillaYawStep — use vanilla 22.5° steps for Shift/Ctrl (default true; set false to use RotationStepDegrees)
  • AllowAnySurface — after tilting, place non-build pieces on walls/ceilings/slopes (default true; never on Build / Heavy Build)
  • AlignToSurface — after tilting, align non-build pieces to walls/ceilings (default true; never on Build / Heavy Build)
  • SuppressSnapWhileRotating — skip snap while Shift/Ctrl held during rotation (default true)
  • ResetRotationKey — key to reset current piece orientation (default J)
  • DebugLogging — log rotation changes to BepInEx

Notes

  • Client-side only
  • Still respects no-build zones, private areas, and biome restrictions
  • Hammer Build and Heavy Build pieces keep vanilla snap after tilt
  • Works best on rotatable hammer pieces

安裝與使用 安裝：BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體，通常是 BepInEx 外掛（解壓後得到 .dll 或外掛資料夾）。
  2. 建議流程：用社群模組管理器（如 r2modman）選中本遊戲後匯入該模組，管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程：先在遊戲目錄裝好 BepInEx 載入器，再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲，BepInEx 控制台會列印載入日誌；確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝，否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時，主機與所有用戶端需要安裝一致的模組。

前置依賴

下面這些內容需要先安裝，否則該模組不會生效：

denikson-BepInExPack_Valheim

檔案與校驗

檔案名稱
FlipIt-1.0.0.zip
檔案大小
131.3 KiB