FlareArrow

版本 v0.2.3·更新於 2026-09-14

A craftable arrow that rises fast then falls slowly while glowing, lighting up dark areas like a flare.

截圖 共 2 張

模組介紹 作者原文

Flare Arrow

A craftable arrow for Valheim that rises fast into the air, then ignites and drifts slowly back down under a bright glow — like a flare gun round. Great for lighting up dark nights, marking a spot across the map, or signaling to other players.

Screenshots

How It Works

  • Fire it like a normal arrow. It arcs upward just like any other shot.
  • The instant it reaches the top of its arc, it "ignites": most of its forward speed is shed, gravity is cut way down, and it starts glowing and trailing sparks as it drifts back to the ground.
  • The glow fades out over a couple of seconds after it lands (or after it's been in the air too long, in case it falls in water or off the map).
  • World wind pushes the glowing arrow and its spark trail around as it falls, so a windy day will carry it sideways.

Crafting

Craft at a Workbench (level 2):

| Requirement | Amount |

|---|---|

| Wood | 8 |

| Resin | 8 |

| Feathers | 2 |

| Greydwarf Eye | 5 |

Yields 20 arrows per craft.

Damage

Low pierce damage (1), high fire damage (28) — this is a utility/light arrow first, a weapon second.

Configuration

Every part of the flight, glow, and spark behavior is tunable via a BepInEx config file (or Configuration Manager in-game), synced for server-wide consistency:

  • Arrow physics — how fast it falls after ignition, how much forward speed it sheds, how strongly wind steers it and how quickly it responds to wind changes, and a safety timeout for stray shots.
  • Flare — the glow's brightness, range, fade duration, and visible size.
  • Spark trail — how the particle trail behaves: lifetime, size, its own independent wind push, gravity, emission rate, and speed.

Requirements

  • BepInEx
  • Jötunn, the Valheim Library

Compatibility

Built without patching any core Valheim classes — all custom behavior lives on this mod's own cloned prefabs, so it should play nicely alongside other bow/arrow mods and hold up across Valheim updates.

Credits

Author: ZimTown

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

denikson-BepInExPack_ValheimValheimModding-Jotunn

檔案與校驗

檔案名稱
FlareArrow-0.2.3.zip
檔案大小
159.9 KiB