KraberOpticSeat

Kraber Optic Seat — Kraber 瞄具底座修正

EN — Repositions the Kraber's optics so their mounts actually sit on the picatinny rail instead of floating above it.

中文 — 修正 Kraber 三種瞄具的安裝位置，讓鏡座真正坐在皮卡丁尼導軌上，而不是懸空。

What it changes / 修改內容

Each optic's geometry is rigidly weighted to its own bone, so the patch simply shifts those vertices along the weapon's up axis (model units).

| Optic | 瞄具 | Adjustment / 位移 |

| --- | --- | --- |

| Threat Scope | 威脅視鏡 | −0.23 |

| Variable Zoom | 可變焦 | −0.035 |

| Stock optic | 原廠瞄具 | +0.01 |

Before / After / 修改前後

Left = original (mount floating above the rail), Right = patched.

左＝原版（鏡座懸空於導軌之上），右＝修正後。

[IMAGE PLACEHOLDER] — replace with a hosted URL of preview_compare.png

（圖片需要上傳到外部圖牀後把鏈接填到這裏； 不渲染 zip 內的相對路徑圖片）

Install / 安裝

EN — Unzip into your Titanfall2 folder so that the mods folder merges with Titanfall2\R2Northstar\mods. Then enable KraberOpticSeat in the Northstar mods menu (it is enabled by default when listed in enabledmods.json).

中文 — 解壓到 Titanfall2 目錄，讓 mods 文件夾與 Titanfall2\R2Northstar\mods 合併即可。之後在北極星的模組菜單裏啓用 KraberOpticSeat。

Manual path / 手動路徑:

Titanfall2\R2Northstar\mods\KraberOpticSeat\

mod.json

mod\models\weapons\at_rifle\ptpov_at_rifle.mdl

Compatibility / 兼容性

• Client-side only. Other players will not see it. It changes no damage, spread, ballistics or hit registration.

純客戶端，其他玩家看不到。不影響傷害、散佈、彈道與命中判定。

• This mod replaces the entire ptpov_at_rifle.mdl. Any other mod that also replaces this file will conflict with it (whichever loads later wins). If you use a Kraber model/skin mod that ships its own.mdl, do not enable both.

本模組替換整個 ptpov_at_rifle.mdl，與任何同樣替換該文件的模組衝突（後加載者生效）。如果你的 Kraber 皮膚模組自帶.mdl，不要同時啓用。

• Mods that only change weapon config values (e.g. weapon-position mods that edit viewmodel_offset_ads) do not conflict at file level, but their values were tuned for the original geometry, so the aiming composition will stack. Disable them if the view looks off.

只改武器配置值的模組（例如調整 viewmodel_offset_ads 的武器位置模組）不會文件衝突，但那些數值是針對原始幾何調的，同時使用時瞄準時的構圖會疊加。

Notes / 備註

• The stock optic (v_scope_dcom) and the variable zoom (v_scope_talon) received very small corrections; the threat scope received the largest one.
• The Kraber's unused stabilizer optic is intentionally left untouched.
• The kill counter (Pro Screen) is not covered by this release — its display mesh is a separate model.

擊殺計數器（Pro Screen）本版未包含——它的顯示網格是獨立模型。

• Fixing attachment seating requires moving the optic's own geometry, not just a config offset: the mount's underside is not flat, so no single viewmodel offset can make it sit flush.

修正嵌合必須動瞄具自身幾何，單靠配置偏移做不到——鏡座底面本身不平整。

Credits / 致謝

Model geometry is Respawn's original asset; this patch only translates part of its vertices.

模型幾何爲 Respawn 原始素材，本補丁僅平移了其中部分頂點。