DontBlink

版本 v1.1.1·更新於 2024-01-31

Adds a blinking mechanic à la SCP: Containment Breach to the game.

截圖 共 1 張

模組介紹 作者原文

"Do not Blink!" by ᴏʀɪᴏɴ™

This mod aims to somewhat mimic the blink mechanic of SCP: Containment Breach. It is obviously not 100% accurate.

INFORMATION

So, all this mod does is simulate the act of blinking. Mind you, it doesn't serve much purpose, unless you are near a Coil-Head that is...

Basically, you will randomly, and periodically blink for a really short amount of time.

Both the interval and duration of a blink are randomly chosen between two values (min & max).

They also scale based on your insanity level kindly provided by the game.

The more insane you are, the more you will blink.

The interval at which you blink is directly displayed right under your sprint meter as a horizontal progress meter enterily made of [, ▓, ░ and ].

The meter continuously drains down until you blink, and refills right after. Remember, each blink interval is different, so the meter will never drain at the same speed.

If you need to refill your blink-meter, press C on your keyboard to manually blink and set your next blink to a fixed 14s (default). This will start a new blink cycle.

Last bit of info, you can keep your eyes closed (surely a Bracken won't kill you...), and while you do, your insanity will slowly decrease, which in turn makes blinking less frequent.

CONFIGURATION

  • Almost all values are editable in the.cfg inside config folder created by BepInEx insde.\Lethal Company\BepInEx. The file should be named.DontBlink.cfg.
  • If you do not want any random factor in blink duration/interval, simply use the same value on both 'min' and 'max'.
  • Side note, as of the latest version (1.1.0), all blink related values were modified to be as close as possible to SCP:CB values (the random aspect was kept), you may need to either delete the.cfg file or edit it manually if you had a previous version. Leave it be if you want to keep old values.

COMPATIBILITY

InsanityRemastered

There shouldn't be any conflict.

OPTIONAL FEATURES

All optional features are disabled by default, but you are free to enable them if you wish.

  • GAS LEAK RAPID METER DRAIN:
  • while you are inside a gas/steam leak, your blink meter will rapidly drain.
  • Multiply the meter drain by 4 (default).
  • Uses the same logic as the 'VISIBILITY LOW' warning, so it may not trigger on some case.
  • NATURAL BLINK ONLY ACTIVE AFTER SEEING A COIL-HEAD.:
  • natural blink is disabled and the hud meter is hidden, but when you see a coil-head, they will appear and function normally.
  • The natural blink and hud last for 5 seconds (default).
  • The Ghost Girl can also trigger it.
  • BLINK ON FEAR:
  • whenever you'd gain a sudden surge of fear based on certain events, you will blink.
  • Some of these events are: Thumper's screech, seeing the Bracken, being too close to a creature, getting hit, seeing a body, etc.
  • This feature has 3 states (has to be edited inside the.cfg):
  • 0 = Disabled (default).
  • 1 = Randomly blink based on the 'fear event' potency. Stronger fear = higher chances of blinking.
  • 2 = Always blink when feared (not recommended).
  • There is an internal cooldown of 1s (default). I strongly recommend to NOT go below 0,5s.
  • This feature should be compatible with InsanityRemastered. Do note it is NOT hooked to IR's hallucinations events etc.

INSTALLATION (MANUAL)

NOT YET MODDED (no BepInEx) (click to open)

  • Download BepInEx 5.4.21 from either its page or its official GitHub. Latest version should be fine too.

Inside the downloaded.zip, extract the folder and both.dll and _config.ini inside your game folder (where the game.exe is located).

If downloaded through, they are stored inside the folder.

  • Run the game once to generate all folders and files, then exit the game when the game menu appears.
  • You are now done with BepInEx!
  • Download DontBlink and extract.dll from inside the.zip to.\Lethal Company\BepInEx\plugins.
  • You are done! Enjoy!

PLANS

  • Make the player react to more events.
  • Make the blink meter an actua

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

BepInEx-BepInExPack

檔案與校驗

檔案名稱
DontBlink-1.1.1.zip
檔案大小
87.8 KiB