Valheim Paintings
Frame part of your screen, paint it, and hang the picture on your walls with the hammer. Each painting carries its own image.
截圖 共 1 張
模組介紹 作者原文
Valheim Paintings
Stop on a ridge at sunset, hold a key, and take the view home. This mod paints part of your
screen onto two planks of wood, and the painting hangs on your walls like any other piece.
Painting
Hold P. The game's interface goes away and a frame shows the square that will be
painted, with the rule of thirds drawn inside it. You keep control while you hold the key:
walk, turn, pull the camera in or out until the view is right. Let go and it is painted.
A painting costs 2 wood. It arrives in your inventory as a Painting item, its icon
being the picture itself, so a chest full of them reads at a glance.
Hanging
The hammer's Furniture tab has a Painting piece, whose only cost is one Painting. It is
a 2 x 2 panel of planks standing upright, the picture covering its whole face. The
placement preview shows the painting that will go up, and the hammer menu shows it as the
piece's icon.
The panel snaps edge to edge with its neighbours, so a gallery lines up by itself. Hold
the alternate placement key (left shift by default) to place it freely.
Taking it down
Removing a painting with the hammer drops it on the ground with its picture, ready to hang
somewhere else. A painting destroyed by damage falls with its picture too: a troll going
through your house does not erase a view you cannot take again. DropOnDamage turns that
off.
To get rid of a painting for good, feed it to an obliterator.
Where the picture lives
In the painting itself. The image is a small JPEG, 384 pixels and at most 32 KB by
default, stored in the item's data and then in the piece once it hangs. It follows the
painting into chests, onto the ground, into your character save and into the world save.
Settings
BepInEx/config/Tchernobill.Valheim_Paintings.cfg, written on first launch.
| Key | Default | What it does |
| --- | --- | --- |
| Enabled | true | master switch, nothing is hooked when false |
| CaptureKey | P | held to frame, released to paint; F11 and F12 are taken by the game and by Steam |
| WoodCost | 2 | wood taken for one painting |
| DropOnDamage | true | a painting destroyed by damage drops with its picture instead of being lost |
| ScreenFraction | 0.5 | side of the painted square, as a fraction of the screen height |
| ThirdsGrid | true | draw the rule of thirds inside the frame |
| TextureSize | 384 | side of the picture a painting carries, in pixels |
| JpegQuality | 75 | quality of that picture, lowered automatically to fit under MaxBytes |
| MaxBytes | 32768 | hard ceiling for one painting's picture |
| ExportPng | false | also save each capture as a full resolution png, a copy for you to keep |
| ExportFolder | empty | where those png files go; empty writes under BepInEx/config/Valheim_Paintings/ |
| CanvasGap | 0 | distance between the picture and the planks, only useful if wood shows through |
| Diagnostics | false | log the geometry of every painting as it appears |
TextureSize and MaxBytes are what a painting costs in the world save. The defaults leave room for a large gallery; raise them for sharper pictures on a
world with few paintings.
The png export is never read back and never deleted by the mod. Destroying a painting in
the game does not touch the copy on your disk.
Check my other mods
安裝與使用 安裝:BepInEx 外掛
- 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
- 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
- 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
- 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。
帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。
下面這些內容需要先安裝,否則該模組不會生效: