PaddlePower

版本 v1.0.2·更新於 2021-03-07

More ship passengers means more hands to help paddle

模組介紹 作者原文

A small thematic mod to make it more fun to sail around with friends.

Features

  • Each additional passenger increases the speed that ships move when in paddle mode (forward or back 1 arrow speed)
  • Speed increase is configurable, and defaults to a geometric series sum with a = 1/2, r = 7/8, and n = passenger count

Known issues

  • All users on a server should have the mod installed to minimize issues
  • Logging out or disconnecting while on the deck of a ship may cause the passenger count to be incorrectly increased until all players leave the area

Pre-Requisites

This mod requires BepInEx. Follow the instructions here if you don't have it installed already:

Installation

  • Extract the archive into a folder. Do not extract into the game folder.
  • Move the contents of "plugins" folder into "\Bepinex\plugins"
  • Start the game

Configuration

Configuration file is located at "\Bepinex\config\ohmg.mods.paddlepower.cfg"

"enabled": enables or disables this plugin in its entirety

"debug_logging": enables or disables printing debug log messages. Kind of spammy and not necessary unless you're trying to figure out a particular issue

"counting_method": What players to count as contributing to ship speed

  • ALL: All players on the deck of the ship
  • ATTACHED: (default) Only count players on the ship that are seated or holding onto the mast or bow
  • SEATED: Only count players that are seated (includes pilot)

"scaling_method" selects which formula to use for calculating player speed contributions

  • GEOMETRIC: (default) Each additional player contributes a diminishing amount of extra speed
  • LINEAR: Each additional player contributes the same amount of extra speed

GEOMETRIC specific configuration properties:

  • Check out for a primer on geometric series
  • The "coefficient" and "ratio" properties correspond to "a" and "r" in the article
  • The "ratio" configuration property is constrained to between 0 and 1

LINEAR specific configuration properties:

  • "base_amount": Paddle force contributed by the ship pilot
  • "additional_amount": Paddle force contributed by each additional player
  • "maximum_bonus": Maximum paddling force, regardless of player count

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

denikson-BepInExPack_Valheim

檔案與校驗

檔案名稱
PaddlePower-1.0.2.zip
檔案大小
27.1 KiB