HexBaseEnhancements
Configurable quality-of-life improvements for your Valheim base.
截圖 共 1 張
模組介紹 作者原文
HexBaseEnhancements
Adds configurable quality-of-life improvements for your Valheim base, including faster resting, automatic repairs, automatic fireplace refueling, faster doors, automatic door closing, and an increased comfort radius.
Screenshots
Features
- Configurable Rested status effect delay
- Automatically removes the Wet status effect when sheltered and near a fire
- Rapidly restores health and stamina while resting
- Automatically repairs damaged inventory items when sheltered and near a fire
- Displays a notification and optionally plays the vanilla repair sound when items are repaired
- Automatically refuels nearby fireplaces when they are almost empty
- Uses fuel from the player's inventory and nearby containers
- Configurable fireplace detection radius from 5 to 100 meters
- Greatly increases door opening speed
- Automatically closes opened doors after a configurable delay
- Configurable comfort detection radius from 1 to 50 meters
Rested Improvements
HexBaseEnhancements allows the delay before receiving the Rested status effect to be customized.
The default custom delay is:
2 seconds
The custom delay can be disabled to restore Valheim's normal behavior.
When rapid health and stamina regeneration is enabled, health and stamina are quickly restored while resting.
Wet Status Removal
When enabled, the Wet status effect is automatically removed when the player is both:
- Sheltered
- Near a fire
Automatic Inventory Repair
When enabled, damaged repairable items in the player's inventory are automatically repaired when the player is sheltered and near a fire.
When one or more items are repaired:
- A notification is displayed
- The vanilla repair sound can optionally be played
Automatic Fireplace Refueling
When enabled, nearby fireplaces are automatically refueled when their fuel level becomes almost empty.
Fuel can be pulled from:
- The player's inventory
- Nearby containers
The default fireplace detection radius is:
20 meters
The detection radius can be configured between:
5 - 100 meters
Only fireplaces within the configured detection radius of the player will be automatically refueled.
Nearby fuel containers are also discovered using this radius. This means a fireplace may be within range, but if the container holding its required fuel is outside the configured detection radius, that fuel will not be available for automatic refueling.
For larger bases, increase the detection radius or distribute fuel containers throughout the base so the required resources remain within range.
Resources are only consumed when a fireplace is almost empty and needs to be refueled. Fireplaces that already have sufficient fuel are left unchanged.
Fireplaces configured with infinite fuel are ignored.
Door Improvements
Doors can be configured to open significantly faster than normal.
Automatic door closing can also be enabled with a configurable delay.
If a door is manually closed before the auto-close timer expires, it will remain closed.
Comfort Radius
Valheim normally detects comfort-providing pieces within approximately 10 meters of the player.
HexBaseEnhancements allows this radius to be configured between:
1 - 50 meters
The default custom comfort radius is:
20 meters
Disabling the increased comfort radius restores the vanilla 10 meter radius.
Configuration
Configuration options are available in:
BepInEx/config/com.hex.baseenhancements.cfg
Wet Debuff
- RemoveWetDebuff — Automatically remove the Wet status effect when sheltered and near a fire
Resting
- CustomRestedDelay — Enable or disable the custom Rested status effect delay
- RestedDelayInSeconds — Number of seconds before receiving the Rested status effect
Health and Stamina Regen
- EnableRapidHealthAndStaminaRegen — Enable rapid health and stamina recovery while resting
Auto-Repair
- EnableAutoRepair — Automatically repair damaged inventory items when sheltered and near a fire
- EnableAutoRepairSound — Play the vanilla repair sound when items
安裝與使用 安裝:BepInEx 外掛
- 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
- 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
- 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
- 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。
帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。
下面這些內容需要先安裝,否則該模組不會生效: