Gizmo

版本 v1.16.0·更新於 2026-09-14

Comfy version of Gizmo.

模組介紹 作者原文

ComfyGizmo

Comfy version of Gizmo.

Features

  • Configurable modifier hot-keys for:
  • X-axis rotation (default: hold LeftShift)
  • Z-axis rotation (default: hold LeftAlt)
  • Reset selected axis rotation (default: V)
  • Reset ALL axis rotations (disabled by default)
  • Can disable the Gizmo placement visual.
  • Can set the snap angles per 180 degrees from 2 - 256.
  • Original Euler-style rotation.

Rotation Modes

Local Frame Mode

  • Allows rotation around the piece's local Y axis rather than the world Y axis.
  • If roof mode was enabled, it is disabled when local frame mode is enabled.

Old Rotation Mode

  • Uses rotation scheme from ComfyGizmo v1.2.0 - v1.4.0.
  • Differs from default by behavior when rotating around multiple axes.

Roof Mode

  • Allows rotations for the 8 corner-roof pieces with the x-z axes shifted 45 degrees about Y.
  • Rotations align with the beam of the roof to sync with inclined flat roof pieces.
  • Will be disabled on enabling Local Frame mode.
  • Is only active when one of the 8 corner-roof pieces are selected.
  • Can remain enabled unless a player wishes to rotate a corner roof piece along its tradtional x or z axes.

Configuration

Ignoring Rotation

Prefabs can be ignored for Gizmo-rotation during placement using the following config-options under [Ignored].

  • ignoreTerrainOpPrefab
  • If enabled, rotation will be ignored for terrain-modifying prefabs.
  • ignorePrefabNameList
  • Comma-separated toggle-list of values where Gizmo-rotation will be ignored for prefabs with matching names.
  • Each value is in the format of: prefab_name=0 or prefab_name=1 where 0|1 indicates toggled off/on.
  • Example: Beech_Sapling=1,Birch_Sapling=1,VineGreen_sapling=1
  • Implements a custom user-friendly UI accessible in ConfigurationManager.

Installation

Manual

  • Unzip ComfyGizmo.dll to your /valheim/BepInEx/plugins/ folder

(manual)

  • Disable or uninstall any installed ComfyGizmo_v1.8.0 or earlier.
  • Go to Settings > Import local mod > select ComfyGizmo_v1.15.0.zip.
  • Click "OK/Import local mod" on the pop-up for information.

Notes

  • See source at: GitHub.
  • Looking for a chill Valheim server? Comfy Valheim Discord
  • ComfyGizmo icon created by @jenniely (jenniely.com)

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

denikson-BepInExPack_Valheim

檔案與校驗

檔案名稱
Gizmo-1.16.0.zip
檔案大小
68.1 KiB