Fleyta

版本 v1.0.0·更新於 2026-10-07

Shove a beached boat back into the water.

模組介紹 作者原文

Fleyta

Fleyta lets you shove a beached boat back into the water. Stand beside a boat that is aground,

press the shove key (B by default), and it slides toward the nearest water until it floats.

Then the boat is the game's again. It does nothing to a boat that is already afloat, and

nothing to the raft.

Why

Vanilla gives a player on foot no way to move a boat at all. A hull run onto a beach is

recoverable only by climbing aboard and rowing against the sand, or by waiting for waves that

may never come. That is the whole annoyance, and this is the whole fix. It is deliberately

narrower than the things it could have been: it does not push you off a dock while aboard, it

does not nudge a boat along open water, and it does not drag a boat across land. One

gesture, for the one situation the game has no answer to.

Two design calls follow from that.

The direction comes from the terrain, not from you. The mod finds the nearest direction in

which the ground drops to floating depth, without first climbing a ridge, and pushes that way.

Standing on the sea side and pressing the key still sends the boat to the sea, because "which

way is the water" is a fact about the boat's position and not about yours. If no water is

within 30 metres, nothing moves and you are told so. A boat left halfway up a beach is worse

than one that stayed put.

The key is a key, not hold-E. A hull has nothing to hover over: the only thing the crosshair

can land on is the helm, where E already means "take the wheel", and holding it would fight

the tap that boards. The helm's hover text names the shove key when pressing it would do

something.

How it feels

  • One press, 20 stamina, and the boat slides at a walking pace until it is over water deep

enough to float. Nothing to hold, no need to stay.

  • A heavier hull is slower. The speed scales with the square root of the hull's mass, so a

longship is slower than a karve by seconds and not by minutes.

  • It refuses, and says why, when the boat is already afloat, when someone is aboard, when

you are out of reach, or when the water is too far.

Installing

Needs BepInEx. Nothing else. Through a mod manager it is one install. By hand, put

Fleyta.dll in BepInEx/plugins/Fleyta.

Then start the game once and quit. That first run writes the config file. It does not exist

before the mod has loaded, which is the usual reason people think it is broken.

Settings

The file is BepInEx/config/ezomic.valheim.fleyta.cfg. Open it in any text editor. Every

setting has a comment above it, so the file explains itself. The two worth knowing first are

FloatDepth, how deep the sea floor must be before a boat counts as afloat, and BaseSpeed.

Neither was measured against the real hulls when the mod was written, so they are the numbers

to tune if a boat stops in the shallows or the slide feels wrong. Turning Verbose on writes

each decision, including the hull's real mass, to the log.

Note that changing a default in a new version does nothing on a machine that has already run

the mod. BepInEx writes every entry on first run and the saved value wins.

Needs a play test

Not run in game yet, and never in a world with other players, so the hand-over to the boat's

owner described under Multiplayer is unproven. Two settings depend on a vanilla behaviour that could only be read

from the code. An unattended hull is damped hard in the water: the game multiplies its

horizontal speed by 0.1 every physics step while nobody is aboard and the hull's centre is

0.5 m or more under the water line. A shove therefore does not coast into the sea, and where

the hull is already in that regime but not yet over FloatDepth the push crawls. Tune

FloatDepth and Acceleration together: a FloatDepth that is too deep makes the last

metres crawl, an Acceleration that is too low makes them stall. Verbose logs where a

shove ends.

Multiplayer

Everyone needs it. A boat is moved by whichever player's game owns it, and force applied

from any other machine is silently thrown away.

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

denikson-BepInExPack_Valheim

檔案與校驗

檔案名稱
Fleyta-1.0.0.zip
檔案大小
88.8 KiB