CrossbowSprintReload

版本 v1.1.1·更新於 2026-07-11

Reload crossbows while sprinting; faster reload while walking; keep loaded only when holstered on back.

模組介紹 作者原文

Crossbow Sprint Reload

Reload crossbows while sprinting, with movement-based reload speed and optional keep-loaded when holstered on your back.

Behavior

| State | Reload |

|-------|--------|

| Sprinting | Allowed, vanilla speed |

| Standing / walking | Allowed, faster (default 1.5×) |

| Jump | Still cancels reload (optional config to keep it) |

| Holster on back (R) | Optional: stay loaded |

| Unequip / hotbar swap | Must reload |

Vanilla clears the action queue every sprint tick, which cancels crossbow reload. This mod keeps the reload action through that clear.

Works with Weapon Holster Overhaul (R = holster to back).

Config (F1 / Configuration Manager)

  • Allow Sprint Reload — default on
  • Non-Sprint Reload Speed — 1.0–3.0, default 1.5
  • Allow Jump Reload — default off
  • Keep Loaded When Holstered — default on (only while on the back via R / HideHandItems; not when fully unequipped)
  • Affect Dundr — default on

Install

  • Install BepInExPack Valheim
  • Install this mod with your mod manager (r2modman / Gale) or drop the DLL into BepInEx/plugins

Changelog

1.1.1

  • Keep-loaded only applies when holstering to the back (R / HideHandItems, e.g. Weapon Holster Overhaul)
  • Fully unequipping or swapping via hotbar clears the load and requires a reload again

1.1.0

  • Added Keep Loaded When Holstered
  • Compatible with Azumatt SaveCrossbowState (defers if that mod is present)

1.0.1

  • Fixed inconsistent sprint reload
  • Fixed non-sprint speed often not applying
  • More stable sprint detection (run key held counts as sprint)
  • Default non-sprint speed raised to 1.5× (range up to 3.0)

1.0.0

  • Initial release
  • Sprint reload at vanilla speed
  • Faster reload while standing or walking (configurable)

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

denikson-BepInExPack_Valheim

檔案與校驗

檔案名稱
CrossbowSprintReload-1.1.1.zip
檔案大小
88.6 KiB