Comfortometer
A compact HUD panel that stays up while you move: every piece giving you comfort, its distance, duplicates in range, and what you just walked out of range of, in red.
模組介紹 作者原文
Comfortometer
What is giving you comfort right now, how far away is it, and what did you just walk out of range of?
Press F4 and a small panel appears on the HUD. It stays up while you move around, so you can walk through your base and watch the comfort level change, and see exactly which piece changed it.
Comfort 14 sheltered · rested 18 min
Hearth +3 2.4 m
Dragon bed +2 4.1 m
Raven throne +3 3.0 m
Black marble table +2 3.3 m
Deer rug ×2 +2 1.8 m
Chair (chair) +1 2.2 m
Banner +1 12 m
Each line is one kind of piece: its comfort points and the distance to the nearest one. When more than one of the same kind is in range the line says so, as in Deer rug ×2, which is your cue that the second one is doing nothing.
Red is the line you are here for. Walk out of range of something and it stays on the list in red, with its current distance, so you know what you lost and how far back it is. It drops off once you are well clear of it. An unlit fire is red too, marked unlit, and when you are not under a roof the header says NO SHELTER in red, because then nothing counts.
Dimmed lines are pieces that give nothing because a better piece of the same group is also in range: a chair next to a throne, a stool next to a chair. The group is named in brackets so you can see why. They are off by default; turn on Show Superseded to see them.
The list is built exactly the way the game builds the comfort level: the same 10 m radius, the same one-per-group and one-per-name rule, the same shelter test. The level in the title is the game's own number.
Moving and resizing
With the panel up, press F4 again to free the mouse. The title strip drags the panel, the grip in the lower-right corner resizes it, and the x in the corner closes it. You can still walk around meanwhile. Press F4 once more to give the mouse back to the camera. The position and size are remembered.
The x and the drag also work whenever the cursor is already free, such as with the inventory open.
The panel grows and shrinks to fit its list, so the grip only changes the width. Turn off Auto Height to set a fixed height instead; then a list that does not fit ends in +N more.
Installing
Client-side. Install it on the computers that should see the panel; nothing goes on the server.
Configuration
BepInEx/config/DeathMonger.Comfortometer.cfg. Every setting takes effect immediately.
| Setting | Default | What it does |
| --- | --- | --- |
| Mod Enabled | true | Master switch. |
| Toggle Panel | F4 | Shows the panel; while it is up, frees or locks the mouse so you can drag, resize or close it. |
| Open At Start | false | Show the panel as soon as you spawn in. |
| Forget Beyond | 30 | A piece you walked out of range of stays listed in red until you are this many meters from it. |
| Show Superseded | false | Also list, dimmed, the pieces in range that give nothing because of a better one in their group. |
| Show Rested Time | true | Show how long Rested lasts at the current comfort level, next to the level. |
| Show Range | false | Show each distance against the range it counts within, as in 8.2 / 10 m. The range is 10 m for every piece, fixed by the game. |
| Bold Names | true | Draw the piece names in bold. |
| Auto Height | true | The panel grows and shrinks to fit its list; the grip t
安裝與使用 安裝:BepInEx 外掛
- 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
- 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
- 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
- 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。
帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。
下面這些內容需要先安裝,否則該模組不會生效: