BetterBallistas

版本 v1.0.0·更新於 2026-09-11

Adjust the firing arc, detection range, speed, targeting and trophy limit of the ballista

模組介紹 作者原文

Better Ballistas

Adjust the firing arc, detection range, speed, targeting and trophy limit of the ballista.

  • Adjust the firing arc of the ballista up to 180 degrees. Use fewer ballistas to cover your base.
  • Adjust the range at which the ballista will find and engage enemies.
  • Adjust the scan speed and idle time at the end of the sweep. See _Tuning_ below.
  • Adjust the number of trophies/enemy types that can be added to the ballista to target.
  • Set targeting options for the ballista. Enable/disable options in-game.

New

  • Updated for Valheim 1.0

Configuration

Ammunition

Maximum Ammo: The maximum amount of ammo that can be loaded into a ballista.@

Scanning

Scan Arc: Total number of degrees the ballista will sweep through during its scanning.@

Sweep Interval: The time interval in which the ballista will complete one sweep (back and forth) within the scan arc.@

Turn Rate: The rate at which the ballista will turn when there's no target.@

Targeting

Maximum Target Trophies: The number of trophies that can be loaded for the ballista to target.@

Target Players: If enabled, the ballista will target players in range.@

Target Tames: If enabled, the ballista will target tames in range.@

Target Enemies: If enabled, the ballista will target enemies in range.

Range: The range at which the ballista will find and engage enemies.@

Utility

LogLevel: Controls the level of information contained in the log

In-game reconfiguration

You can use Configuration Manager (or similar) mod to change the configuration without exiting the game. Changing the config file will also reload the configuration.

Tuning

You can adjust several parameters to increase or decrease the turret motion of the ballista. The Scan Arc, Sweep Interval and Turn Rate all work together to tune the scanning action.

  • The _Scan Arc_ determines the total number of degrees the ballista will sweep through. Note that larger arcs take more time to complete a sweep.
  • The _Sweep Interval_ is the time in which a sweep will 'complete'. It is the time the ballista will 'use' to complete its sweep, including the rotation as well as the pauses at the end of the travel.
  • Setting the interval shorter will result in less pause time at the end of the travel, but if set too short, will cut off the sweep and reverse direction before the full sweep is completed.
  • The _Turn Rate_ is the speed (degrees per second) at which the turret will rotate through its sweep.
  • A faster turn rate will complete its rotation sooner, allowing you to reduce the _Sweep Interval_ to minimize the time spent paused at the end of the travel.

Notes

  • Valheim already had the capability to load more than one trophy to the ballista to allow targeting multiple creature types! They just didn't let you.
  • Azumatt's ImFRIENDLYDAMMIT will override the Target Player and Target Tames setting. You don't need to run this mod if you're using BetterBallistas.

Compatibility issues & defects

  • If you find a compatibility issue please post it on mod-help on Discord. Be sure to include the mod name and version you think may be incompatible.
  • If you have a bug please report it in mod-help on Discord. If you do post a bug report, please make sure to include the following:
  • Your version of this mod
  • What you were doing, or attempting to do when it happened
  • If it's repeatable - i.e., can you duplicate it?
  • The exact behavior you observed (or didn't observe)
  • If possible, post a capture of the log file with errors (errors always begin with this mod's name) on Discord

You can find all Neobotics released mods on:

-: NeoboticsOnThunderstore

-: NeoboticsOnNexus

  • Hexium: NeoboticsOnHexium

Your comments and feedback are always welcome. Post or Discord: NeoboticsOnDiscord

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。 多人連線時,主機與所有用戶端需要安裝一致的模組。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

denikson-BepInExPack_Valheim

檔案與校驗

檔案名稱
BetterBallistas-1.0.0.zip
檔案大小
164.7 KiB