自定義燈

作者 Azazellz·版本 v1.0·更新於 2019-06-18

具有廣泛定製選項的隱形光源。

截圖 共 8 張

模組介紹 作者原文

具有廣泛定製選項的隱形光源。靈感來自Quick Light mod。

要打開按住“E”按鈕(“使用”按鈕)。

有許多選項可用於配置:

  • 顏色淺,範圍很廣。使用RGB(紅 - 藍 - 綠)機制。
  • 光源類型。一個有陰影,兩個沒有陰影。
  • 光半徑。最大 - 最多5000個單位。
  • 淡淡的褪色。
  • 相對於玩家的輕微位置。
  • 光源將附加到的角色骨架中的節點。
  • 按住按鈕激活時間。

還提供其他預先創建的照明選項,包括兩種面部照明選項。

與FaceLight和FaceLight Plus沒有衝突(內置檢查來自這些mod的活動照明法術的存在)。

由於使用了相同的激活機制,因此可能與QuickLight發生衝突。

可能與“可穿戴”光源或“燭光”香草法術上的其他模組發生衝突。

要求

  • SKSE64
  • SkyUI SE
  • PO3的Papyrus Extender
  • NetImmerse Override或RaceMenu

安裝

共同。

卸載

使用特殊按鈕im MCM。關閉所有菜單。等待5秒鐘,直到您看到任務已停止。

之後,您可以保存遊戲並刪除mod。

傳奇版可在此處獲得。

謝謝:

Kerber100有助於編寫腳本

tktk1 for Quick Light

Papyrus Extender的力量

——————————————————————————————————————————

Invisible light source with extensive customization options. Inspired by Quick Light mod.

To turn on hold "E" button ("use" button).

There are many options available for configuration:

-- Light color, in very wide limits. Use RGB (red-blue-green) mechanics.

-- Type of light source. One with shadows and two without shadows.

-- Light radius. Maximum - up to 5000 units.

-- Light fade.

-- Light position, relative to the player.

-- The node in the skeleton of the character to which the light source will be attached.

-- Hold button activation time.

Additional pre-created lighting options are available, including two options for face lighting.

No conflicts with FaceLight and FaceLight Plus (built-in check for the presence of active lighting spells from these mods).

A conflict with QuickLight is possible, since the identical activation mechanism is used.

There may be a conflict with other mods on "wearable" light sources or with the "Candlelight" vanilla spell.

Requirements

-- SKSE64

-- SkyUI SE

-- PO3's Papyrus Extender

-- NetImmerse Override or RaceMenu

Install

Common.

Uninstall

Use special button im MCM. Close all menus. Wait 5 seconds until you see that the quest has been stopped.

After that you can save the game and delete the mod.

Legendary Edition version available here.

Thanks to:

Kerber100 for help in scripting

tktk1 for Quick Light

powerofthree for Papyrus Extender

安裝與使用 安裝:按包內說明操作

  1. 解壓本站下載的壓縮包,先讀包內的 readme / 說明檔案。
  2. 這類遊戲沒有通用的模組管理器:有的模組直接替換遊戲檔案、有的放進遊戲專屬的 Mods 資料夾、有的要先裝遊戲對應的社群載入器或工具,以包內說明為準。
  3. 嚴格按說明放置檔案;標註「前置依賴」的模組需要把依賴一併裝好。
  4. 啟動遊戲確認載入成功;部分遊戲需要在設定或模組選單裡手動啟用。

不同遊戲、不同模組的安裝位置差異很大,包內說明是最可靠的依據。

檔案與校驗

檔案名稱
自定义灯
檔案大小
42.4 KiB