Squidos Sprint Crosshair

版本 v1.3.0·更新於 2026-10-09

Sprint Crosshair Configurations!!!

模組介紹 作者原文

Squido's Sprint Crosshair

Adjusts the sprint crosshair to be added onto your crosshair, rather than replacing it, allowing you to see your spread and other survivor specific THANGS like FS' Spikes.

Additionally, allows you to color the crosshair itself while sprinting. The color is configurable, but by default uses a similar color to the sprint icon in the bottom right next to your abilities.

(NEW!) Additionally^2 allows you to increase the spread of your crosshair while sprinting if you don't like the arrow OR the coloring option (but both can also be used alongside this option!)

Fully customizable, with built in manually adjusted default configs for all vanilla survivors, and additions made for any modded survivors:D

Config

Supports RiskOfOptions (optional)

Otherwise edit

BepInEx/config/FluxSquido.SquidosSprintCrosshair.cfg.

General (applies to everyone)

  • Enabled - Enable or disable the mod entirely
  • Max Opacity - how visible the arrow is while sprinting (0 to 1).
  • Fade In Seconds / Fade Out Seconds - how long it takes for the crosshair to fade in/out, by default off entirely.

Crosshair Coloring

  • Crosshair Sprint Color - the global hex color (RRGGBB, default A3E3FF) that the crosshair tints to for any survivor with Color Crosshair turned on. Has to be manually edited in the cfg file because Risk Of Options doesn't support it. The color you pick is shared, but which survivors use it is per-survivor.

Global Crosshair Behaviors (turns an option on for every character at once. While one is on, each survivor's own matching option is grayed out, and their settings are kept for when you turn it back off)

  • Color Crosshair For All Characters - turns Color Crosshair on for every character.
  • Increase Spread For All Characters - turns Increase Spread While Sprinting on for every character. Each survivor's Spread Increase Multiplier still controls how much.
  • Remove Sprint Crosshair For All Characters - turns Remove Sprint Crosshair on for every character, so nobody gets the sprint arrow.

Survivor Options - every survivor gets their own section:

  • Use Vanilla Sprint Crosshair - turns the mod off for that survivor, so their crosshair is replaced by the sprint crosshair like the base game. The options below are ignored for them when this is on.
  • Remove Sprint Crosshair - keep the normal crosshair while sprinting with no arrow.
  • Use Generic Sprint Arrow - use the plain arrow instead of a survivor's custom sprint crosshair. Only shown for survivors that have one (Operator and some modded survivors), to show things like Operator's primary-charge display.
  • Scale - size of the arrow (1 = vanilla sprint crosshair size).
  • Vertical Offset - pixels above the crosshair (negative = below).
  • Horizontal Offset - left/right nudge in pixels (0 = centered).
  • Tilt - rotation in degrees (positive = clockwise).
  • Color Crosshair - while sprinting, tint the crosshair itself (not the arrow) to the Crosshair Sprint Color.
  • Increase Spread While Sprinting - visually spreads the crosshair a little more while sprinting. Purely cosmetic, it does NOT change your real spread.
  • Spread Increase Multiplier - how much extra spread to show (1 = the default amount). Applies whether spread is on from this survivor's toggle or from Increase Spread For All Characters.

Bodies that aren't survivors (like Heretic or Remote Operation Drones) use the Other Characters section.

INSPIRATIONS!!!

RemoveSprintingCrosshair by Disro

WolfoQualityOfLife by Wolfo (which, among other things, adds an option to make the sprint crosshair show your spread a little better. You should probably turn that off if using this.)

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

bbepis-BepInExPack

檔案與校驗

檔案名稱
Squidos_Sprint_Crosshair-1.3.0.zip
檔案大小
24.9 KiB