SecondWalkies

版本 v4.0.0·更新於 2026-09-23

【HostOnlyMOD】Buy up to two Semibot Walkies boxes, one at a time, with the vanilla blue pair second. ホスト導入だけで、トランシーバーを1箱ずつ最大2箱まで購入でき、2箱目はバニラの青色ペアになります。

模組介紹 作者原文

SecondWalkies

English

Overview

SecondWalkies lets the team buy up to two boxes of Semibot Walkies during a run. The first box contains the vanilla red pair, and the second contains the vanilla blue pair.

Only the host needs SecondWalkies. There are no settings to configure.

Requirements

  • BepInExPack 5.4.2305 or a later compatible version

Installation

Install with a compatible mod manager, or place SecondWalkies.dll in the profile's BepInEx/plugins directory. Only the host needs the mod.

Behavior

  • The team can buy up to two Semibot Walkies boxes during a run.
  • The shop offers no more than one box at a time.
  • The first box contains the vanilla red pair, and the second contains the vanilla blue pair.
  • The second box can appear on a later shop visit after the first has been purchased.
  • Price, shop selection chance, and walkie behavior remain unchanged.

Multiplayer

  • Only the host needs SecondWalkies.
  • Participants without the mod can use both pairs normally.
  • The purchase limit and shop stock are controlled by the host.

Compatibility

  • MoreShopItems Updated 4.2.2: compatible
  • NoItemSpawnLimit 1.0.8: compatible
  • JettsShopConfig 1.3.0: not supported for combined use
  • MoreStandsForShops 1.1.1: not supported for combined use

日本語

概要

SecondWalkiesは、1回のランでセミボットトランシーバーを最大2箱まで購入できるようにします。1箱目にはバニラの赤色ペア、2箱目にはバニラの青色ペアが入ります。

ホストだけの導入で利用できます。設定項目はありません。

必須MOD

  • BepInExPack 5.4.2305以降の互換バージョン

導入方法

対応するMODマネージャーでインストールするか、SecondWalkies.dllをプロファイルのBepInEx/pluginsへ配置してください。導入が必要なのはホストだけです。

動作

  • 1回のランでセミボットトランシーバーを最大2箱まで購入できます。
  • ショップに並ぶ箱は一度に最大1箱です。
  • 1箱目はバニラの赤色ペア、2箱目はバニラの青色ペアです。
  • 1箱目を購入すると、その後のショップで2箱目が出現候補になります。
  • 価格、ショップでの出現確率、トランシーバーの機能は変わりません。

マルチプレイ

  • 導入が必要なのはホストだけです。
  • MOD未導入の參加者も両方のペアを通常どおり使用できます。
  • 購入上限とショップ在庫はホストが管理します。

互換性

  • MoreShopItems Updated 4.2.2:対応
  • NoItemSpawnLimit 1.0.8:対応
  • JettsShopConfig 1.3.0:併用非対応
  • MoreStandsForShops 1.1.1:併用非対応

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

BepInEx-BepInExPack

檔案與校驗

檔案名稱
SecondWalkies-4.0.0.zip
檔案大小
207.5 KiB