OmniDirectionalMobilityGear
Spawn with an unlimited right-hand grappling launcher. RMB fires and pulls; LMB climbs. Inspired by Attack on Titan. Experimental single-player-tested release; multiplayer unverified.
模組介紹 作者原文
Omni-Directional Mobility Gear
A right-hand grappling launcher for PEAK, inspired by Attack on Titan's ODM gear.
Spawn with your gear already equipped. Fire at terrain, pull yourself toward it, and use PEAK's normal wall climbing when you reach the surface. No inventory slot or ammunition is needed.
This is an experimental, single-player-tested release. Multiplayer and full-run compatibility have not been verified.
Controls
| Input | Action |
| --- | --- |
| Right mouse button | Fire at the aimed surface and pull toward it. Click again to redirect. |
| Hold left mouse button | Grab and climb a nearby wall; move with WASD. |
| Release left mouse button | Let go of the wall. |
| Space | Disconnect the cable. Normal jumping remains available. |
| F6 | Enable or disable gear mode. Disable it to use normal item and help/reach controls. |
Gear mode starts enabled. Your starting held item is stowed automatically. Clicking either mouse button in gear mode also stows a held item; it is kept in your inventory.
Features
- Automatically equips a permanent right-hand launcher when your local character spawns.
- Unlimited uses with a 0.22-second firing interval.
- Default range: 40 game units. Default target pull speed: 16 units per second.
- Automatically releases on arrival, after six seconds, if the anchor disappears, or when climbing begins.
- Releases when player input is blocked, focus is lost, or the character becomes incapacitated.
- English controls and status display.
Normal climbing still consumes stamina. Fall damage still applies after releasing the hook.
Installation
Install Mod Manager or r2modman, including the BepInExPack_PEAK dependency, then launch modded PEAK. Start with Play Solo for this release.
For manual installation, install BepInExPack_PEAK first, then copy this package's BepInEx/plugins/PeakOdmGear directory into your game's BepInEx/plugins directory.
Restart the game after installing or updating the mod.
Configuration
After first launch, settings are generated in:
BepInEx/config/dev.midor.peak.odmgear.cfg
- Gear / Range: maximum grapple distance, 5-120 game units.
- Gear / PullSpeed: target pull speed, 4-30 units per second.
- Display / ShowHud: show or hide the English control hints.
Current limitations
- Hooks terrain and surfaces. Hooking or rescuing teammates is not implemented.
- Other players do not receive synchronized launcher/cable visuals.
- Multiplayer, controllers, full mountain runs, and combinations with other input or climbing mods have not been tested.
- This release uses a single hook. Dual hooks, gas tanks, blades, and anime character models are not included.
Validation
Tested in PEAK v2.6.a, Unity 6000.3.15f1, with BepInEx 5.4.23.3.
Automated tests ran inside the actual game: automatic equipment, 100 consecutive shots, nearest-surface selection, measured character pulling, disconnect, missing targets, mouse input routing, native wall climbing and release, and restoration of normal controls when disabled. The equipped model was also checked in an in-game capture.
Physical mouse playtesting and an entire mountain run remain unverified.
Credits
Mod concept and direction: Rachel560lu. Code developed with AI assistance.
The launcher appearance is read from your installed PEAK game at runtime; no PEAK game assets or game assemblies are bundled. This is an unofficial fan mod inspired by Attack on Titan. Source code is maintained in a private repository.
安裝與使用 安裝:BepInEx 外掛
- 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
- 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
- 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
- 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。
帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。
下面這些內容需要先安裝,否則該模組不會生效: