FrogQTE

版本 v1.0.1·更新於 2026-08-16

Mash Space to escape the frog.連續點按空格讓你掙脫青蛙。

模組介紹 作者原文

FrogQTE

Mash Space to escape the frog

Highlights

  • When the frog grabs you, press Space enough times within the time limit to escape.
  • If you escape in time, the frog lets go and your stun is cancelled.
  • Skeletons are immune to the FlyTrap debuff (no more shattering when it fills up), but can still mash Space to escape the frog.
  • The frog's tongue lock-hold time is adjustable.
  • All key values are configurable via the BepInEx config file.

Configuration

The mod creates a BepInEx config file after first launch. Common options include:

| Setting | Purpose |

| --- | --- |

| Enabled | Enable or disable the frog-capture QTE |

| FlyTrapAmount | FlyTrap status (fraction of HP) applied when the frog grabs you |

| PressesToEscape | How many Space presses it takes to escape |

| EscapeTime | Seconds you have to mash Space and escape |

| EscapeThreshold | FlyTrap status below which the frog lets go |

| HoldTime | Seconds the frog holds you (tongue stuck) before pulling |

Installation

  • Install BepInEx for PEAK.
  • Put FrogQTE.dll into:

BepInEx/plugins/

  • Launch the game, get grabbed by a frog, and mash Space to escape.

Feedback

If you find a bug in this mod, please DM me on Discord at @luoyuyue515, or send an email with the error report to luoyuzhouablny@qq.com.

中文介紹

連續點按空格讓你掙脫青蛙。

主要功能

  • 青蛙抓住你時,在限時內按夠次數的 空格鍵 即可掙脫。
  • 成功逃脫時,青蛙會鬆開你,並取消眩暈
  • 骷髏狀態免疫捕蠅草負面狀態(不會因狀態漲滿而碎掉),但仍可正常連按空格掙脫青蛙。
  • 青蛙舌頭鎖住你的持續時間可調節。
  • 所有關鍵數值都可通過 BepInEx 配置文件修改。

配置項

首次啓動遊戲後,模組會生成 BepInEx 配置文件,常用選項包括:

| 配置項 | 作用 |

| --- | --- |

| Enabled | 啓用/禁用青蛙抓捕 QTE |

| FlyTrapAmount | 被青蛙抓住時施加的捕蠅草狀態(佔生命值比例) |

| PressesToEscape | 需要連按多少次空格才能逃脫 |

| EscapeTime | 連按空格逃脫的時間限制(秒) |

| EscapeThreshold | 捕蠅草狀態低於該值時青蛙會鬆開 |

| HoldTime | 青蛙用舌頭鎖住你的持續時間(秒),之後開始拉拽 |

安裝方法

  • 安裝 PEAK 對應的 BepInEx。
  • 將 FrogQTE.dll 放入:

BepInEx/plugins/

  • 啓動遊戲,被青蛙抓住後連按 空格鍵 即可逃脫。

反饋

如果 mod 出 bug 了,請在 B 站聯繫 “落羽之月所言”。

安裝與使用 安裝:BepInEx 外掛

  1. 本站下載的壓縮包就是模組本體,通常是 BepInEx 外掛(解壓後得到 .dll 或外掛資料夾)。
  2. 建議流程:用社群模組管理器(如 r2modman)選中本遊戲後匯入該模組,管理器會自動裝好 BepInEx 前置並處理依賴。
  3. 手動流程:先在遊戲目錄裝好 BepInEx 載入器,再把解壓出的 .dll 或外掛資料夾放進 BepInEx/plugins/。
  4. 啟動遊戲,BepInEx 控制台會列印載入日誌;確認這個模組出現在日誌裡即為安裝成功。

帶「前置依賴」的模組需要一併安裝,否則不會載入。功能開關通常在遊戲內或外掛自帶的設定檔裡調整。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

BepInEx-BepInExPack_PEAK

檔案與校驗

檔案名稱
FrogQTE-1.0.1.zip
檔案大小
95.1 KiB