BunnyHop

版本 v1.0.0·更新於 2026-08-27

Adds bunny-hopping to How To Fish: auto-jump while holding the jump key and a speed boost while airborne, plus a simple speed/status HUD.

模組介紹 作者原文

🐇 Bunny Hop

**Bunny-hop your way across the map in How To Fish.

Auto-jump while holding the jump key, get a speed boost while airborne or mid-chain, and keep an eye on your speed with a lightweight HUD.

✨ Features

  • 🐇 Auto bhop — hold the jump key and it jumps for you the instant you land, no manual timing needed
  • 🚀 Airborne speed boost — a configurable speed cap that only applies while airborne or during the landing "grace window," so normal ground movement stays untouched
  • 📊 Speed HUD — current speed in km/h plus a BHOP ON/OFF status, shown top-right
  • ⚙️ Fully configurable — tune the speed cap, grace window, auto-jump, and HUD independently
  • 🔑 In-game toggle key — turn the whole mod on/off instantly without touching menus

🎮 How it works

  • Hold your jump key while moving.
  • The mod auto-jumps you the moment you touch ground (if AutoBhop is enabled).
  • While airborne — and briefly after landing — your speed cap is raised above normal sprint speed, letting good strafing chain into real speed gains.
  • Watch the top-right HUD: the big number is your current speed in km/h, and the line below shows whether bhop is currently active.

💡 Tip: Press F7 (default, configurable) any time to toggle the whole mod on/off — handy if you want to play normally for a bit.

💡 Tip: If the speed boost feels too strong or too weak, tune AirSpeedCap in the config — it's the hard ceiling applied while airborne/chaining.

💡 Tip: If jumps feel like they cut off your chain too easily, raise BhopGraceWindow slightly (e.g. 0.15–0.2) to give yourself more leeway after landing.

⚙️ Configuration

Config file generated on first launch at:

BepInEx/config/neko.howtofish.bunnyhop.cfg

| Section | Setting | Default | Description |

|---|---|---|---|

| General | Enabled | true | Master on/off switch for the mod. |

| General | ToggleKey | F7 | Hotkey to toggle the mod on/off in-game. |

| Bhop | AutoBhop | true | Automatically jump while the jump key is held. |

| Bhop | AirSpeedCap | 14 | Horizontal speed cap while airborne/mid-chain. Set higher than your normal sprint speed to feel a real boost. |

| Bhop | BhopGraceWindow | 0.12 | Seconds after landing during which the raised speed cap still applies — your timing window to chain the next jump. |

| Hud | HudEnabled | true | Shows the speed/status HUD in the top-right corner. |

📥 Installation Mod Manager / r2modman: just click Install — dependencies are handled automatically.

Manual install:**

  • Install BepInEx for How To Fish, if you haven't already.
  • Drop the mod's.dll into BepInEx/plugins.
  • Launch the game once to generate the config file, then tune settings to taste.

🧩 Compatibility & known issues

  • Speed boost only applies while airborne or briefly after landing — normal ground walking/sprinting is untouched.
  • HUD shows -- until your local player has fully spawned in.
  • This mod only affects your own local movement, not other players' clients.

🐛 Found a bug?

Please report it with as much detail as possible (a BepInEx log helps a lot) — happy to take a look!

🙏 Credits

Made by Neko (NekoCuteJs).

Happy hopping! 🐇

安裝與使用 安裝:按包內說明操作

  1. 解壓本站下載的壓縮包,先讀包內的 readme / 說明檔案。
  2. 多數模組依賴遊戲的模組載入器:常見做法是用社群模組管理器(如 r2modman)選中本遊戲安裝,由管理器自動處理載入器與依賴。
  3. 手動安裝時,把模組檔案放進遊戲目錄下對應的 Mod / plugins 資料夾。
  4. 啟動遊戲確認載入成功;帶「前置依賴」的模組需要把依賴一併安裝。

不同模組的安裝位置差異較大,包內說明是最可靠的依據。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

BepInEx-BepInExPack

檔案與校驗

檔案名稱
BunnyHop-1.0.0.zip
檔案大小
57.4 KiB