EnhancedControls

版本 v1.0.1·更新於 2026-08-05

Control and movement quality-of-life improvements for Big Walk. 爲 Big Walk 提供更順手的操作與移動優化。

模組介紹 作者原文

Enhanced Controls

Control and movement quality-of-life improvements for Big Walk.

Features

  • Quick Low-Posture Exit

While sitting, sliding, or transitioning, press Sit, Sprint, or Jump to stand up immediately.

  • Raised-Prop Lock Speed

Shortens the hold time needed to lock the raised-prop pose.

  • Jump Assist

Adds a 0.12-second jump buffer before landing and 0.10-second coyote time after passively walking off jumpable ground. Normal jumps do not create coyote time, so this does not add double jumps.

  • Auto Run

Toggle continuous forward movement with a configurable keyboard or gamepad key. Press the key again, or press forward/backward again, to stop it. The status label follows the game language.

Installation

  • Place EnhancedControls.dll in Big Walk/BepInEx/plugins.
  • Launch the game once. The configuration file is created at BepInEx/config/mhz.bigwalk.enhancedcontrols.cfg.

Configuration

All features are enabled by default and can be changed in the BepInEx configuration file.

| Setting | Description | Default |

| --- | --- | --- |

| Quick Low-Posture Exit | Immediately stand up with Sit, Sprint, or Jump while sitting, sliding, or transitioning. | Enabled |

| Raised-Prop Lock Speed | Shortens the hold time required to lock the raised-prop pose. | Enabled |

| Jump Assist | Queues a jump pressed before landing and allows jumping briefly after walking off a ledge. | Enabled |

| Auto Run Key | Keyboard key that starts or stops Auto Run. | X |

| Auto Run Gamepad Key | Gamepad key that starts or stops Auto Run. | JoystickButton2 |

Support

If you enjoy the mod, you can buy me a coffee on Ko-fi ☕.

Enhanced Controls

爲 Big Walk 提供更順手的操作與移動優化。

功能

  • 低姿態快速退出

坐下、滑鏟或過渡時,按坐下、奔跑或跳躍可立即起身。

  • 舉物鎖定提速

縮短舉高道具時鎖定姿態所需的長按時間。

  • 跳躍優化

加入 0.12 秒的落地前跳躍緩衝,以及走出可跳躍地面後的 0.10 秒土狼時間。正常起跳不會觸發土狼時間,不會形成二段跳。

  • 自動奔跑

通過可配置的鍵盤或手柄按鍵切換持續前進;再次按下該鍵,或重新按前進/後退即可結束。狀態提示會隨遊戲語言顯示自動奔跑、自動奔跑或 AUTO RUN。

安裝

  • 將 EnhancedControls.dll 放入 Big Walk/BepInEx/plugins/。
  • 啓動一次遊戲後,配置文件會生成在 BepInEx/config/mhz.bigwalk.enhancedcontrols.cfg。

配置

所有功能默認開啓,可在 BepInEx 配置文件中修改。

| 設置 | 說明 | 默認值 |

| --- | --- | --- |

| 低姿態快速退出 | 坐下、滑鏟或過渡時,按坐下、奔跑或跳躍可立即起身。 | 開啓 |

| 舉物鎖定提速 | 縮短舉高道具時鎖定姿態所需的長按時間。 | 開啓 |

| 跳躍優化 | 落地前按跳會自動起跳,走出平臺邊緣後短暫仍可跳躍。 | 開啓 |

| 自動奔跑鍵盤按鍵 | 開始或結束自動奔跑的鍵盤按鍵。 | X |

| 自動奔跑手柄按鍵 | 開始或結束自動奔跑的手柄按鍵。 | JoystickButton2 |

支持

如果你喜歡這個 MOD,歡迎在 Ko-fi 請我喝杯咖啡 ☕。

安裝與使用 安裝:按包內說明操作

  1. 解壓本站下載的壓縮包,先讀包內的 readme / 說明檔案。
  2. 多數模組依賴遊戲的模組載入器:常見做法是用社群模組管理器(如 r2modman)選中本遊戲安裝,由管理器自動處理載入器與依賴。
  3. 手動安裝時,把模組檔案放進遊戲目錄下對應的 Mod / plugins 資料夾。
  4. 啟動遊戲確認載入成功;帶「前置依賴」的模組需要把依賴一併安裝。

不同模組的安裝位置差異較大,包內說明是最可靠的依據。

前置依賴

下面這些內容需要先安裝,否則該模組不會生效:

BepInEx-BepInExPack_IL2CPP

檔案與校驗

檔案名稱
EnhancedControls-1.0.1.zip
檔案大小
41.6 KiB